Jeep Wrangler 3.8L Engine 2008-2011 Refurbished Engine R8144470AD Mahle Melling

$3,399.00

  • Brand: Jeep
  • Availability: 2 In Stock
  • SKU: 68426944AE
  • Barcode:

**Engine Assembly: Completely Sealed and Ready for Installation****Ready to Ship with No Wait Times!***NO CORE CHARGE***Included Components:**- Long Block Assembly- Micro polished OEM Crankshaft Balanced to Perfection- New Clevite Main and Rod Bearings   P/N CB1410A(6)  P/N MS1946P and P/N MS1946A- New Mahle Pistons and Rings (Addresses Ring Land Issue) P/N 2243444WR020  20 Over - New Melling Oil Pump Timing Cover (Will...

Tags:

**Engine Assembly: Completely Sealed and Ready for Installation**


**Ready to Ship with No Wait Times!**


*NO CORE CHARGE*


**Included Components:**


- Long Block Assembly

- Micro polished OEM Crankshaft Balanced to Perfection

- New Clevite Main and Rod Bearings   P/N CB1410A(6)  P/N MS1946P and P/N MS1946A

- New Mahle Pistons and Rings (Addresses Ring Land Issue) P/N 2243444WR020  20 Over 

- New Melling Oil Pump Timing Cover (Will assist with amending the Rod Bearing issues these motors 

are known to have)  P/N MOC417 we will not reuse or rebuild oil pumps ever High Volume Brand New High Flow 

Oil Pump 

- New OEM Timing Kit

-New Pickup Tube 04666028AA

- New Water Pump

- OEM Shot-peened Rods, Re-rounded with All Rods Inspected and Reservice (New Pin Bushings) If the rod was spun prior we will not use that rod ! 

- New  Head Gasket OEM 

- New OEM Valve Seals OEM

- OEM Cut & Lapped Valves (3 Angle, 44/45 Degrees) New Valves Springs retainers and Locks ! 

- Valve Cover New 

- Oil Pan New 

- Sealed Oil Pan

- ARP Head Bolts ** Why not we fixed the oiling issue lets hold some power ! 


- Cylinder Heads

  - Valves Inspected; New Valves Installed if Necessary

  - Valve Guides Swapped if Out of Tolerance

  - Springs Tested to Meet OE Spring Pressure Rating

  - New Valve Locks Used (Known to Wear on this Engine)

  - Valves Cut to 3 Angles (44/45 Degrees)

  - All Cylinders Pull 25 lbs of Vacuum

  - Resurfaced to a Near Mirror Finish

Cam Bearings are Replaced and Re Clearance Cam Tunnels are inspected

All Flashing are removed from our engines ! 


We not only Rebuild our engine we figure out why they are failing and fortify !  


**Warranty Information:**


For your peace of mind, all rebuilt engines come with a 6-month, 8,000-mile limited warranty on the long block assembly. Please note that normal wear and tear is not covered. For detailed warranty terms and conditions, please contact the seller.


**Installation Instructions for Engine Longevity:**


1. After engine installation, disconnect the 4 coil-packs and crank the engine in 3 - 5 second intervals to prime the motor with oil before startup, ensuring proper lubrication.

2. Reconnect the coil packs and start the vehicle.

3. Allow the engine to idle for 30 minutes, clearing any engine codes with an OBDII Scanner during this time.

4. After 30 minutes, shut off the vehicle and drain the oil and oil filter, following proper disposal procedures.

5. Inspect the drained oil for abnormalities, contacting us immediately if anything unusual is noticed.

6. Install a new oil filter and fill the engine with recommended high-quality engine oil.

7. Start the vehicle again, allowing it to idle to circulate the new oil.

8. Congratulations! Your engine is now properly installed and ready for use. Follow the recommended maintenance schedule for optimal performance.



You can add, text, html, images and videos as well to the tab from product settings area

Tags:

Recently Viewed Products

$3,399.00